RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: aaronforth
Showing results 1 to 23 of 23
Search took 0.07 seconds.
Forum: KingTech Turbines International
07-27-2020, 11:16 PM
Replies: 137
Views: 24,742
Posted By aaronforth

why run 2 RX batteries ? If you dont trust your...

why run 2 RX batteries ? If you dont trust your system fix it ! Dont rubber band it !
Forum: KingTech Turbines International
07-27-2020, 11:13 PM
Replies: 137
Views: 24,742
Posted By aaronforth

Why not have a power backup? Will it hurt...

Why not have a power backup? Will it hurt anything....no...will it possibly prevent a flame out due to a power issue....yes....

I can only suggest tricks...cant persuade people to use them.....
Forum: KingTech Turbines International
07-25-2020, 07:10 PM
Replies: 137
Views: 24,742
Posted By aaronforth

AUX RX is the one you want

AUX RX is the one you want
Forum: KingTech Turbines International
07-24-2020, 05:13 PM
Replies: 137
Views: 24,742
Posted By aaronforth

thanks for the permission 🤣

thanks for the permission 🤣
Forum: KingTech Turbines International
07-24-2020, 05:06 PM
Replies: 137
Views: 24,742
Posted By aaronforth

your right it's not required...running duel...

your right it's not required...running duel batteries are not required either....

I knew somebody that had a flame out due to a poor contact on the throttle cable. A second lead would have...
Forum: KingTech Turbines International
07-24-2020, 04:59 PM
Replies: 137
Views: 24,742
Posted By aaronforth

Lol that's like saying I dont have Insurance but...

Lol that's like saying I dont have Insurance but it's ok I haven't been an an accident lol

And the AUX port is there right up to the G4 series
Forum: KingTech Turbines International
07-24-2020, 04:52 PM
Replies: 137
Views: 24,742
Posted By aaronforth

Yes I always run a second lead to the AUX port on...

Yes I always run a second lead to the AUX port on ECU as a power backup....
Forum: KingTech Turbines International
08-18-2018, 02:39 PM
Replies: 137
Views: 24,742
Posted By aaronforth

Did you go into the telemtry module setup screen...

Did you go into the telemtry module setup screen and select Futaba ?

for Spektrum just use the xbus...see my previous posts for spektrum...
Forum: KingTech Turbines International
02-25-2018, 01:57 PM
Replies: 137
Views: 24,742
Posted By aaronforth

it works the same way, you have to interrupt...

it works the same way, you have to interrupt power...I have both
Forum: KingTech Turbines International
02-25-2018, 10:36 AM
Replies: 137
Views: 24,742
Posted By aaronforth

Exactly! Too bad Spektrum wasn't that easy lol ...

Exactly!
Too bad Spektrum wasn't that easy lol

Once the system is powered up, your way will work!
Trick is getting the system to initialize first !
Forum: KingTech Turbines International
02-25-2018, 08:12 AM
Replies: 137
Views: 24,742
Posted By aaronforth

I would think the same goes for Jeti. Power must...

I would think the same goes for Jeti. Power must be interrupted to reset the fuel.
Forum: KingTech Turbines International
02-24-2018, 06:50 PM
Replies: 137
Views: 24,742
Posted By aaronforth

If you use the new Spektrum powersafe RX you have...

If you use the new Spektrum powersafe RX you have to do something similar.

I tap into the power wire on the Xbus wire with a diode, run that to the power wire of the JR wire with another diode....
Forum: KingTech Turbines International
02-24-2018, 06:46 PM
Replies: 137
Views: 24,742
Posted By aaronforth

I use Spektrum with Powerbox Mercury. The...

I use Spektrum with Powerbox Mercury.
The Spektrum Xicoy Telemetry needs power at startup in order for the Spektrum Xbus to find it and initialize it. The problem is with a RX controlled switch it...
Forum: KingTech Turbines International
02-24-2018, 03:20 PM
Replies: 137
Views: 24,742
Posted By aaronforth

Yes you can use a receiver controlled switch. If...

Yes you can use a receiver controlled switch. If you're using Spektrum it takes a little more wiring. The easiest way is with the push button
Forum: KingTech Turbines International
02-24-2018, 02:42 PM
Replies: 137
Views: 24,742
Posted By aaronforth

There's a way yes... what I did is installed...

There's a way yes...

what I did is installed a normally closed push button switch in my air brake compartment. Install the switch on the power lead of the Telemtry module. When the button is...
Forum: KingTech Turbines International
01-17-2018, 07:47 AM
Replies: 137
Views: 24,742
Posted By aaronforth

Do a Flight like you normally would.. after you...

Do a Flight like you normally would..
after you land measure the fuel you have left
Look at the Telemtry fuel remaining

let's say your pump factor was 350 and your fuel left was 58% but your...
Forum: KingTech Turbines International
11-07-2017, 04:18 PM
Replies: 137
Views: 24,742
Posted By aaronforth

Yes I agree that is wierd. I make most of my...

Yes I agree that is wierd. I make most of my extensions and never had an issue.
I have an extension on my telemetry module mounted in my jet. Also an extention on GSU (So 2 extentions in total). All...
Forum: KingTech Turbines International
11-07-2017, 03:19 PM
Replies: 137
Views: 24,742
Posted By aaronforth

The telemetry menu is not in the ECU. It's in...

The telemetry menu is not in the ECU. It's in the telemerty module. Plug your GSU into your telemetry module and you will gain access to the telemetry menu through the radio icon.

hope this helps...
Forum: KingTech Turbines International
07-27-2017, 11:11 AM
Replies: 137
Views: 24,742
Posted By aaronforth

Just a quick note on the Y harness. You...

Just a quick note on the Y harness.

You don't need to cross the wires in the Y harness. Just make a normal Spektrum x-bus Y harness. The wires get crossed into the right orientation when you use...
Forum: KingTech Turbines International
07-25-2017, 11:14 AM
Replies: 137
Views: 24,742
Posted By aaronforth

There is no printed instructions that I know of. ...

There is no printed instructions that I know of.

Jr style plug (3 pin) plugs into the GSU port on ECU. The other end plugs into the telemetry module.

Spektrum cable that is supplied (4 pin)...
Forum: KingTech Turbines International
07-20-2017, 12:37 PM
Replies: 137
Views: 24,742
Posted By aaronforth

Just a quick note. You have to make up a Y...

Just a quick note.

You have to make up a Y harness to get full telemetry from your royal srs. There is only one 4 pin spectrum port on the royal and KT . So make a Y harness and plug it into the...
Forum: KingTech Turbines International
07-20-2017, 12:30 PM
Replies: 137
Views: 24,742
Posted By aaronforth

Glad to hear it's working now

Glad to hear it's working now
Forum: KingTech Turbines International
07-20-2017, 09:43 AM
Replies: 137
Views: 24,742
Posted By aaronforth

I have the exact setup as you do, works flawless....

I have the exact setup as you do, works flawless.
When you say you are not getting data from the KT telemetry are you sure its only KT? Have you tried others? Did you bind the TM1000 is correct...
Showing results 1 to 23 of 23


 
Forum Jump

Contact Us - Manage Preferences - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.