RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: dogshome
Showing results 1 to 17 of 17
Search took 0.02 seconds.
Forum: Gas Engines
07-01-2015, 11:32 AM
Replies: 1,678
Views: 463,111
Posted By dogshome

Tyor - Not run mine yet, I'll check the timing...

Tyor - Not run mine yet, I'll check the timing before I do and set it back from 36 degrees accordingly. I like 4 fingers and 1 thumb on each hand!
Forum: Gas Engines
03-31-2015, 12:35 PM
Replies: 1,678
Views: 463,111
Posted By dogshome

DISCUS - Strange you have a motor with no mounts...

DISCUS - Strange you have a motor with no mounts or ignition??? I can understand the engine getting damaged and/or the mounts, but not the ignition pack.

I would say power of a DLE30. ASP180 on...
Forum: Gas Engines
03-31-2015, 12:24 PM
Replies: 1,678
Views: 463,111
Posted By dogshome

Looks like a potentially difficult flier - like a...

Looks like a potentially difficult flier - like a Geebee!
Do you have a build thread elsewhere on RCU?
Forum: Gas Engines
03-24-2015, 11:49 AM
Replies: 1,678
Views: 463,111
Posted By dogshome

The smaller Just Engines geared starter (or...

The smaller Just Engines geared starter (or similar) will do it. Dynatron if you have more cash. Normal 40/60 size non-geared won't do it. The Lipo powered one by Thunder Tiger would do it too (just,...
Forum: Gas Engines
03-07-2015, 05:25 AM
Replies: 1,678
Views: 463,111
Posted By dogshome

Just need an airframe now :o ...

Just need an airframe now :o

http://i230.photobucket.com/albums/ee268/huntdogshome/IMAG0034_zps7hqkg4rr.jpg (http://s230.photobucket.com/user/huntdogshome/media/IMAG0034_zps7hqkg4rr.jpg.html)
Forum: Gas Engines
03-04-2015, 01:14 AM
Replies: 1,678
Views: 463,111
Posted By dogshome

There are just 2 M3 clearance holes and the M14*...

There are just 2 M3 clearance holes and the M14* 0.75 to take ASP etc flexi pipe.

If I was going to make a right angle one, I'd make the hole 12mm clearance to match the head and cross drill the...
Forum: Gas Engines
03-03-2015, 10:55 AM
Replies: 1,678
Views: 463,111
Posted By dogshome

Not happy with engine mount! So: ...

Not happy with engine mount! So:

http://i230.photobucket.com/albums/ee268/huntdogshome/IMAG0031_zpstpmxgvll.jpg (http://s230.photobucket.com/user/huntdogshome/media/IMAG0031_zpstpmxgvll.jpg.html)
Forum: Gas Engines
03-01-2015, 09:07 AM
Replies: 1,678
Views: 463,111
Posted By dogshome

There isn't enough meat to tap the head. I made...

There isn't enough meat to tap the head. I made an aluminium adaptor, someone else a brass one - earlier in the thread.
Forum: Gas Engines
02-28-2015, 02:13 PM
Replies: 1,678
Views: 463,111
Posted By dogshome

14mm OD. 13mm OD also fine.

14mm OD. 13mm OD also fine.
Forum: Gas Engines
02-22-2015, 06:50 AM
Replies: 1,678
Views: 463,111
Posted By dogshome

That's better ;) Bit of 10mm aluminium drilled...

That's better ;) Bit of 10mm aluminium drilled and tapped 14* 0.75mm and an ASP 180 muffler.

I wish I had a better pillar drill, a couple of attempts were needed to get a nice clean 13mm hole...
Forum: Gas Engines
02-16-2015, 02:42 PM
Replies: 1,678
Views: 463,111
Posted By dogshome

Carb screws wrong length. Carb bracket not...

Carb screws wrong length.
Carb bracket not right (probably explains broken manifolds elsewhere).
Filed and sorted :rolleyes:
...
Forum: Gas Engines
02-13-2015, 09:44 AM
Replies: 1,678
Views: 463,111
Posted By dogshome

A methanol fire can be put out by water and burns...

A methanol fire can be put out by water and burns slower, but you can't see a Methanol fire. Water can be used to put it out, but you can't do that with petrol fires.
Flash point of petrol is -43C,...
Forum: Gas Engines
02-12-2015, 01:29 PM
Replies: 1,678
Views: 463,111
Posted By dogshome

Well I have a GF38 in my hands. A hefty lump! ...

Well I have a GF38 in my hands. A hefty lump!

All the screws need tightening.
The general quality is good, let down by a few poor machining actions.
Very stiff and will need a lot of running in....
Forum: Gas Engines
02-08-2015, 01:58 PM
Replies: 1,678
Views: 463,111
Posted By dogshome

Thanks for dimensions :cool:

Thanks for dimensions :cool:
Forum: Gas Engines
02-08-2015, 01:57 PM
Replies: 1,678
Views: 463,111
Posted By dogshome

Bummer. We aren't allowed jets because of the...

Bummer. We aren't allowed jets because of the fire risk. But no-one here can afford them anyhow! Now I have seen turbines blow up on impact. I've also seen Lipo fires on VERY heavy crashes. Petrol or...
Forum: Gas Engines
02-08-2015, 01:09 PM
Replies: 1,678
Views: 463,111
Posted By dogshome

I live in the UK. Anything slightly noisy risks...

I live in the UK. Anything slightly noisy risks the loss of the flying field. We get this in the BMFA news every few months - it sometimes only takes one complaint. With planning permission, noise...
Forum: Gas Engines
02-07-2015, 07:39 AM
Replies: 1,678
Views: 463,111
Posted By dogshome

Can someone tell me what the O/D of the exhaust...

Can someone tell me what the O/D of the exhaust header is please?

These have a 14mm I/D and the overall size is about the same as an ASP 180 FS muffler.
...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.