RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: mogman
Showing results 1 to 11 of 11
Search took 0.02 seconds.
Forum: Gas Engines
07-13-2014, 05:42 PM
Replies: 1,678
Views: 463,189
Posted By mogman

I believe Pardal stated he had too much play in...

I believe Pardal stated he had too much play in the bearings so he machined some bushings to replace them?
See post # 37
Forum: Gas Engines
07-13-2014, 04:47 PM
Replies: 1,678
Views: 463,189
Posted By mogman

It does have needle brgs. on the rod.

It does have needle brgs. on the rod.
Forum: Gas Engines
06-02-2014, 09:26 PM
Replies: 1,678
Views: 463,189
Posted By mogman

Hi Pardal, Have you done this modification? If...

Hi Pardal,
Have you done this modification? If so, did it improve the vibration level of the engine?

Cheers,
Dave.
Forum: Gas Engines
06-02-2014, 09:25 PM
Replies: 1,678
Views: 463,189
Posted By mogman

Hi Alf. It wasn't listed on their website,...

Hi Alf.

It wasn't listed on their website, so I inquired about them in an e-mail.
Andrew at Justengines was very accommodating and nice to deal with .I don't have the bill of sale anymore, but...
Forum: Gas Engines
06-02-2014, 03:25 PM
Replies: 1,678
Views: 463,189
Posted By mogman

Just Engines will supply only the mufflers. I...

Just Engines will supply only the mufflers. I purchased 2 of them for my Widgeon.
Forum: Gas Engines
05-09-2014, 11:21 AM
Replies: 1,678
Views: 463,189
Posted By mogman

[QUOTE=Pontiac_40;11801153]Nice looking plane...

[QUOTE=Pontiac_40;11801153]Nice looking plane mogman! Good job on the build. What type of mufflers you are using,did you fabricate them yourself?[/QUOTE


The mufflers and header pipes were...
Forum: Gas Engines
05-09-2014, 07:52 AM
Replies: 1,678
Views: 463,189
Posted By mogman

I just finished my winter project, a 120"...

I just finished my winter project, a 120" Grumman Widgeon from G&P Sales. Power is 2 NGH 38cc 4 st., using 17x8 APC, don't remember the rpm numbers.
I broke in the engines on a Great Planes giant...
Forum: Gas Engines
03-08-2014, 05:46 PM
Replies: 1,678
Views: 463,189
Posted By mogman

I'm putting 2 of these into a 1/4 scale Grumman...

I'm putting 2 of these into a 1/4 scale Grumman Widgeon.(120") I've been using a Great Planes giant ugly stick to break in the engines....one at a time. Using 40:1 Stihl ultra. They are mounted...
Forum: Gas Engines
12-29-2013, 07:09 AM
Replies: 1,678
Views: 463,189
Posted By mogman

Let us know if you find someone that carries...

Let us know if you find someone that carries parts. I checked with AMR, from whom I bought my 38's, their reply....no parts available.
I don't need any yet, and I do have a spare engine.
Forum: Gas Engines
12-19-2013, 01:44 PM
Replies: 1,678
Views: 463,189
Posted By mogman

[QUOTE=GalenB;11688718]Hello, I recently...

[QUOTE=GalenB;11688718]Hello,

I recently purchased one of these engines for an ESM Beaver... Fitting it will be a PIA on the Beaver, but then fitting any engine to this plane will be a PIA! :) ...
Forum: Gas Engines
12-06-2013, 08:01 AM
Replies: 1,678
Views: 463,189
Posted By mogman

That's the great thing about Walbro type carbs....

That's the great thing about Walbro type carbs. They have a pump so tank position is a non issue. Doesn't matter if the tank is high, low, far away. I always mount my gas tanks just slightly ahead...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.