RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Ozflyboi
Showing results 1 to 11 of 11
Search took 0.03 seconds.
Forum: Glow Engines
05-24-2016, 04:29 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

I have resolved the issue with the microsens on...

I have resolved the issue with the microsens on board glow unit.

The problem was very simply. The pin jumper which is removed to enter programming mode was in fact missing the tiny metal contacts....
Forum: Glow Engines
05-23-2016, 02:54 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

Hi Linkan2, Last night I did some more...

Hi Linkan2,

Last night I did some more tests on the microsens and I will explain what is happening.

I entered automatic programming mode (jumper removed) and completed the calibration starting...
Forum: Glow Engines
05-22-2016, 02:31 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

Hi Maxam and cymaz, Okay so I have finally...

Hi Maxam and cymaz,

Okay so I have finally worked out what my problem was. This was all due to valve lash being too tight (not enough clearance).
Now that I have the clearances set correctly...
Forum: Glow Engines
05-19-2016, 08:10 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

Thanks for your advice. Yes I have revisited...

Thanks for your advice.

Yes I have revisited my fuel lines and clunk already. I will also take a good look at the intake pipes as you suggested. I noticed the exhaust tubes going into collector...
Forum: Glow Engines
05-19-2016, 04:03 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

Yes agreed that Methanol is Hygroscopic, however...

Yes agreed that Methanol is Hygroscopic, however it is the Nitromethane that encourages rust through its Oxygen carrying properties. It is for this reason for which I avoid it. I have experienced...
Forum: Glow Engines
05-19-2016, 03:17 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

I am little worried of nitro introducing rust to...

I am little worried of nitro introducing rust to this motor. I have been careful to date with using blue block after each session of running. I also use Tri Flow on the rockers to keep them...
Forum: Glow Engines
05-18-2016, 03:00 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

Hi all, As I previously mentioned I was...

Hi all,
As I previously mentioned I was experiencing pushrods dislodging in flight on my 7-35 and since I investigated further I discovered that my valve clearances were incorrectly set as I used...
Forum: Glow Engines
04-28-2016, 10:41 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

Hi Guys, Just thought I would share with you...

Hi Guys,

Just thought I would share with you some photos of my Evo 7-35 I recently installed and test flown in my Great Planes Waco.

The model seems to fly in a scale like fashion with this...
Forum: Glow Engines
04-14-2016, 04:11 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

Hi Maxam, Yes thanks for your advice I have...

Hi Maxam,

Yes thanks for your advice I have two other biela props 17x8 and 17x12 to try with this motor.

I went over the valve adjustment last night and will run the motor this evening to...
Forum: Glow Engines
04-13-2016, 04:36 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

Thanks for the suggestions however I have checked...

Thanks for the suggestions however I have checked all the pushrods and all fine no chips on end caps.

I have located some steel grub screws with Dog Point End on ebay so hopefully will arrive...
Forum: Glow Engines
04-13-2016, 03:00 PM
Replies: 2,647
Views: 522,739
Posted By Ozflyboi

Hi All, I am new to this thread and I am an...

Hi All,

I am new to this thread and I am an owner of Evolution 7-35 glow and 7-160 gas motors.

I have a question, with the 7-35 glow radial I have run into the problem of the push-rods...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.