RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 6
1
2
3
Last »
Search: Posts Made By: F1 Rocket
Showing results 1 to 25 of 128
Search took 0.02 seconds.
Forum: RC Jets
02-26-2024, 01:01 PM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

Failsafe should be set in what ever the servo or...

Failsafe should be set in what ever the servo or device is physically connected to.
Forum: RC Jets
04-16-2023, 01:08 PM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

As has been said, you can set the PB receivers to...

As has been said, you can set the PB receivers to output SBus and then use a serial I/O with the Cortex Pro. The only complicating part of this is if you want to use P2 Bus sensors as well. I’m not...
Forum: RC Jets
02-27-2023, 09:33 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

Factory is working hard to get our order out but...

Factory is working hard to get our order out but it’s probably going to be a couple more weeks.
Forum: RC Jets
02-26-2023, 09:31 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

Nothing special needed. Just make sure the...

Nothing special needed. Just make sure the taileron mix is active when you teach the Cortex Pro the stick movements.
Forum: RC Jets
06-14-2021, 09:12 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

expected the end of this month.

expected the end of this month.
Forum: RC Jets
03-03-2021, 05:30 PM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

Cable loom or serial mode should not make a...

Cable loom or serial mode should not make a difference. At this point I think we should exchange that unit.
Forum: RC Jets
02-27-2021, 10:59 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

This is an issue which has come up a few times....

This is an issue which has come up a few times. The Cortex Pro does not shift the centering. If this is happening it must be something in the SBus output from the RX that is shifted. Please make sure...
Forum: RC Jets
02-22-2021, 04:59 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

You are limited to (6) directly connected...

You are limited to (6) directly connected stabilized outputs when using the supplied cable loom for the input.

An extra directly connected stabilized output (total of 7) is available on port A...
Forum: RC Jets
12-29-2020, 04:52 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

I’ve not tested Spektrum’s version of SRXL but if...

I’ve not tested Spektrum’s version of SRXL but if port A does not have a channel output the most likely reason is that Spektrum do not send data for channel 7.
Forum: RC Jets
11-24-2020, 01:09 PM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

For SBus you can use either 5 or 6.

For SBus you can use either 5 or 6.
Forum: RC Jets
11-24-2020, 12:34 PM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

The outputs from ports 5 and 6 are the same but...

The outputs from ports 5 and 6 are the same but the ports are independent and should not be be connected together.

FYI, your email to bavarianDEMON support was forwarded to me this morning. I saw...
Forum: RC Jets
11-05-2020, 02:01 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

In the serial I/O mode, the Cotex Pro will not...

In the serial I/O mode, the Cotex Pro will not output data when no data is input from the receivers connected to it.
Forum: RC Jets
10-22-2020, 05:33 PM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

Most likely a trim setting has changed or is...

Most likely a trim setting has changed or is changing. Two of the most common causes are nose wheel steering trim changes (if you are running the nose wheel through the gyro) and elevator trim...
Forum: RC Jets
10-04-2020, 02:53 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

Always teach the stick movement at high rate. You...

Always teach the stick movement at high rate. You can then adjust your rates as needed. Inflight gain settings are a function of airspeed not rate.
Forum: RC Jets
09-18-2020, 08:50 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

If you are in North America, please give me a...

If you are in North America, please give me a call. im certain we can get your issues solved.

Danny
AeroPanda
407-687-3126
Forum: RC Jets
08-02-2020, 07:33 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

The Cortex Pro’s inputs are ports A and B. For a...

The Cortex Pro’s inputs are ports A and B. For a single receiver and utilizing the serial output mode of the Cortex Pro you will connect the receiver to port A.
The Cortex Pro’s serial outputs are...
Forum: RC Jets
07-31-2020, 02:30 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

No. The master gain needs to be set at a low...

No. The master gain needs to be set at a low value (best to start at 25%) and then adjusted as needed.
Forum: RC Jets
07-31-2020, 02:27 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

You will need to set your receiver to output...

You will need to set your receiver to output S.Bus with the physical output pins set for channels 9-15.
Plug the S.Bus lead into port A. Plug the control board into port 5 or 6.
Forum: RC Jets
07-31-2020, 02:20 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

The Cortex Pro needs to receive all inputs from...

The Cortex Pro needs to receive all inputs from one receiver. A few guys have tried splitting the inputs and had issues. Please check with the JR team guys and they can tell you which of their...
Forum: RC Jets
07-13-2020, 05:43 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

The advice given in the manual for the Mephisto...

The advice given in the manual for the Mephisto assumes the use of a single Cortex Pro. This may be different since you are using two. The primary thing is that the vector needs more gain then the...
Forum: RC Jets
06-03-2020, 12:02 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

Outputs 5 and 6 are the same data. Connecting...

Outputs 5 and 6 are the same data. Connecting both provides a little extra redundancy. Only output 6 is bidirectional so it needs to be connected to rx1.
Forum: RC Jets
06-02-2020, 01:39 PM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

We do this using a Rex type receiver as the input...

We do this using a Rex type receiver as the input into the cortex pro. Typically we only use one REX into port B of the Cortex Pro. Then configure one of the REX’s E ports to EX Bus Backup Input And...
Forum: RC Jets
05-25-2020, 05:01 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

I prefer running independent channels and being...

I prefer running independent channels and being able to match the travels . If you have achieved this with a simple Y connector then you shouldn’t have a problem.
Forum: RC Jets
05-24-2020, 03:04 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

Yes, but you also have enough ports to run all...

Yes, but you also have enough ports to run all (4) taileron servos through independent channels if you want.
Forum: RC Jets
05-23-2020, 12:42 AM
Replies: 1,019
Views: 274,093
Posted By F1 Rocket

With Spektrum you will need (2) Cortex Pro for a...

With Spektrum you will need (2) Cortex Pro for a full house Mephisto.
Showing results 1 to 25 of 128
 
Page 1 of 6
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.