RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Pete S-RCU
Showing results 1 to 11 of 11
Search took 0.03 seconds.
Forum: Glow Engines
06-21-2016, 11:37 AM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

Maxam, what starter would you recommend for the...

Maxam, what starter would you recommend for the EVO7260 engine?
The Miller's won't turn it over I don't think.
Coleman makes a geared starter that will definitely turn it over, ever used one?
...
Forum: Glow Engines
04-28-2016, 01:10 PM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

Starter

Maxim, I have the Evo7260 gas engine, will a Sullivan Megatron starter turn over a 260 cc engine?
I'm trying to find a starter, not very many choices to choose from.
Forum: Glow Engines
03-29-2016, 06:09 AM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

Proper prop, air speed

OK, if I use a 12x12 say on a smaller engine that I'm used too, I can pretty much know the speed of the plane.
Theoretically, one revolution is 12" of travel.
The big props seem different because...
Forum: Glow Engines
03-26-2016, 11:20 AM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

Hi Tom, I have a question about what prop to...

Hi Tom,

I have a question about what prop to use for flying on my Evo7260 radial.
I'm using a 32x12 for breakin, watching the rpm closely.
This prop is too small, I can exceed 5k at about half...
Forum: Glow Engines
01-27-2016, 08:50 AM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

That's interesting, I should probably consider a...

That's interesting, I should probably consider a 34x18 or so.
Would like to know more before I buy one, they're not cheap.
Forum: Glow Engines
01-27-2016, 08:47 AM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

I have a Eurcoupe with a Saito 57cc twin in it. ...

I have a Eurcoupe with a Saito 57cc twin in it.
It has the CH igniotion system with a rpm output that works with a digital tach, or the TM1000 telemtry module.
Won't work with both at the same time...
Forum: Glow Engines
01-27-2016, 06:29 AM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

The issue is getting a signal to the tach, the...

The issue is getting a signal to the tach, the coil 'might' provide it?
It may also have to be amplified to a usable level?
If so, I could possibly build a little amp with a few op-amps.
Something...
Forum: Glow Engines
01-26-2016, 04:58 PM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

UMS Evolution Radial Care and Operation

You're right, I found where the sensor goes.
Yes, the tach thing will be a problem.
Maybe a coil wrapped around the plug wire would generate enough volta to trigger the tach in the TM1000 rpm...
Forum: Glow Engines
01-21-2016, 10:10 AM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

OK, it's a 34x14 prop, my mistake. More...

OK, it's a 34x14 prop, my mistake.
More questions, the nipple on the exhaust ring is for fuel tank pressure or also I'm thinking smoke oil?
My carb has a primer bulb on it, do I need a tee fitting...
Forum: Glow Engines
01-19-2016, 06:41 AM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

Thanks for the help, I won't get to run it till...

Thanks for the help, I won't get to run it till spring, still kind of cold here in the frozen tundra.(Minnesota)
What kind of oil do you guys use on the valve train?
Does it get messy putting oil...
Forum: Glow Engines
01-18-2016, 04:20 PM
Replies: 2,647
Views: 522,742
Posted By Pete S-RCU

I have the Evo 7260 radial that I'm putting on a...

I have the Evo 7260 radial that I'm putting on a BUSA Stearman.
This is my first radial, so I have a few questions.
I've read most of this thread and didn't see anything about the E7260.
The carb...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.