RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Cattledog
Showing results 1 to 15 of 15
Search took 0.02 seconds.
Forum: Glow Engines
06-07-2016, 01:30 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

A question - does anyone know of a prop hub that...

A question - does anyone know of a prop hub that fits the 7-35 that has 4 or 6 screws?
Forum: Glow Engines
08-10-2014, 09:33 AM
Replies: 2,647
Views: 522,688
Posted By Cattledog

another thing to keep in mind is you might have...

another thing to keep in mind is you might have debris in the needle areas of the carb. This can cause some confusing results when tuning.
Forum: Glow Engines
07-11-2014, 04:45 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

Lars, Something to try, BVM R/C...

Lars,

Something to try,

BVM R/C mixture control unit http://shopbvmjets.com/zencart/index.php?main_page=product_info&cPath=33&products_id=105

I set it up so I am extremely rich on the...
Forum: Glow Engines
11-19-2013, 12:36 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

Bullfrog Performance $35 for 5 gallon pail / if...

Bullfrog Performance
$35 for 5 gallon pail / if you shop the local speed shops you should be able to find it for $4 per gallon if you bring your own plastic container. Bullfrog is out of stock...
Forum: Glow Engines
11-01-2013, 05:30 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

search this site for UncleGeorge (George...

search this site for UncleGeorge (George Jenkins) and he has a nice prop hub that will look good on your bipe....

found him: ...
Forum: Glow Engines
10-11-2013, 01:38 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

all metal has at least some galvanic processes...

all metal has at least some galvanic processes going on. However, when they are next to each other on the chart I posted earlier, they have a very very low potential voltage. In the common metals...
Forum: Glow Engines
10-10-2013, 08:19 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

Picture #3 is the clue... See the bumps in the...

Picture #3 is the clue... See the bumps in the rust. This is indicative of galvanic corrosion, not simple oxidation type corrosion. So, someplace in this motor we have stainless steel (I'm...
Forum: Glow Engines
09-10-2013, 04:15 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

I had all of the plugs out today and they are...

I had all of the plugs out today and they are marked with OS #8..........
Forum: Glow Engines
09-05-2013, 06:55 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

Slot vs Slit when viewed from incoming or...

Slot vs Slit when viewed from incoming or manifold sides?

Also, what glow plug do these engines like?
Forum: Glow Engines
09-05-2013, 12:43 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

So more questions - I purchased 4 sets from...

So more questions - I purchased 4 sets from Phil's and they have arrived. Push rod is identical to existing units - the follower/lifter is different than existing units. On the parts in the engine,...
Forum: Glow Engines
09-04-2013, 03:56 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

Does anyone remember the post number for the...

Does anyone remember the post number for the photos of new vs old carbs on the Evo's?
Forum: Glow Engines
08-29-2013, 03:24 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

Actually, in this case, aluminum is probably a...

Actually, in this case, aluminum is probably a better choice than steel - it grows at the same rate as the rest of the parts and is much much lighter.
Forum: Glow Engines
08-29-2013, 12:46 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

http://www.engineeringtoolbox.com/linear-thermal-e...

http://www.engineeringtoolbox.com/linear-thermal-expansion-d_1379.html

Unless you are doing this on a preheated engine 0.002 might be a little tight. Using the calculator above with starting temp...
Forum: Glow Engines
08-24-2013, 09:54 AM
Replies: 2,647
Views: 522,688
Posted By Cattledog

thank you REDBALL - I don't know if this is of...

thank you REDBALL - I don't know if this is of interest but dry Methanol can be purchased at the following shops. Some will ship too. Current average is $3.70 per gallon.

Alabama

Bessemer...
Forum: Glow Engines
08-23-2013, 04:44 PM
Replies: 2,647
Views: 522,688
Posted By Cattledog

Push Rod Question

Ok, I've been lurking for 5 months and just bought a used 7-35 which arrived today. Somehow during transit, 9 of the pushrods fell out and 4 of the cam followers/lifters fell out. Is this normal to...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.